Diamond F-200

Speaker cabinet design and construction is one of the most critical elements influencing sound performance.
Based on our TLIE – Taga Low Interference Enclosures technology TAGA Harmony have developed a new high-end solution to even more increase stiffness and limit any unwanted resonances of the cabinet.

The new technology is called S-TLIE Super Taga Low Interference Enclosures.

Super rigid and thick 25mm [F-200] or 18mm [B-60] MDF were used for walls and 30mm for the baffle in the F-200 (front panel).

The internal structure of the F-200 was divided in two chambers in an approximate ratio 80% of volume for woofers and 20% for a midrange and tweeter. It allows much better and independent tuning of the low and mid-high sections.

Internal bracing is used to further strengthen the whole structure and achieve even greater rigidity.
The walls are firmly anchored to the 80mm [F-200] and 75mm [B-60] backbone beam highly strengthening the whole construction.

The bent shape of the side walls as well as the curved top plays a significant role in lowering unwanted vibrations, diffraction, turbulences and standing waves effect.

The high-end African wood veneers painted with 9-layer clear piano lacquer is extremely luxurious and enduring.


To keep elegant and sleek appearance of the front panel there are no grill sockets thanks to a magnetic mountable grill. 


The F-200 cabinet sits on a 2-layer discrete metal base with oversized spikes. 
The 2-layer design increases isolation from the floor, the transparency of sound and provides better definition and the basis for the bass.

The whole cabinet is tilted back slightly to time-align all the drivers – it brings the tweeter’s output into the best and correct alignment.

Supplied extra aluminum spike supports (for the F-200) provide super stability for the speakers and protect the floor from being scratched.


HIGH-FREQUENCY DRIVER

1. Additional Φ70 magnet 
2. T-YOKE / Pole piece           
3. Oversized ferrite Φ80 magnet    
4. Top plate                          
5. 28mm CCAW and silver wiring voice coil
6. O-TPTTD (Oversized Taga Pure Titanium Tweeter Dome)
7. E-TPAF (Enlarged Taga Pure Aluminum Faceplate)
8. Metal grill

The high-end 30mm (1.18”) O-TPTTD (Oversized Taga Pure Titanium Tweeter Dome) is 20% bigger than in our Platinum Special Edition series to allow even higher power handling and more accurate, clear, smooth and detailed performance. Ferrofluid cooled and heavy duty 28mm CCAW and silver wiring voice coil as well as 2 magnets (Φ80 &   Φ70) help the tweeter to bear high power. It has exceptional precision and works with ultra-extended high-frequency response up to 33 kHz (+/- 3dB).

The E-TPAF (Enlarged Taga Pure Aluminum Faceplate) and metal grill helps even further dispersion of high-frequencies.


MIDRANGE DRIVER

1. Additional Φ90 magnet
2. T-YOKE / Pole piece                                                                           
3. Oversized Φ100 magnet
4. Top plate
5. Terminal
6. Aluminum injection-molded chassis with anti-oxidation surface process
7. Spider
8. Flat wire copper voice coil
9. E-TPACD (Extended Taga Pure Aluminum cone Driver)
10. Pure aluminum bullet shaped phase plug

The 165mm (6.5”) rigid and ultra-light E-TPACD (Extended Taga Pure Aluminum cone Driver) midrange (with a bullet shaped phase plug,  aluminum chassis and oversized 2-magnet structure Φ100/Φ90) with the butyl suspension can move very fast and frequently allowing mid-range frequencies to be very rich, spacious and sweet.
The still, bullet shaped phase plug is to align the phase of the audio signal and to smooth the midrange frequency response. The extended low and high frequency range (from 46 Hz – 18 kHz) helps overlapping with frequencies of the woofers and the tweeter to offer the best sound consistency and integration.


BASS-MIDRANGE DRIVER / BASS DRIVER

1. Additional Φ110 magnet [F-200 only]
2. T-YOKE / Pole piece                                                                           
3. Two oversized Φ123 magnets [One Φ120 in B-60]
4. Top plate
5. Terminal
6. Aluminum injection-molded chassis with anti-oxidation surface process
7. Spider
8. 4-layer pure copper ribbon voice coil
7. TNPPCD (Taga  Non-pressed Paper Cone Driver)
9. Non-pressed Paper dust cap

The two 203mm (8”) in F-200 and one 165mm (6.5") in B-60 TNPPCD (Taga  Non-pressed Paper Cone Driver) woofers – each equipped with oversized magnets (1 in B-60) and  aluminum chassis. They are extremely rigid and utilize vibration-free solutions. The heavy duty 4-layer pure copper ribbon voice coil allows high power handling. Our TNPPCD drivers offer deep, precise and detailed bass performance. Thanks to a larger surface area to push air – the sound can be played at much louder levels.


BASSREFLEX

BOM Bassreflex Omnidirectional Module (only the F-200) - low-turbulence and high-velocity ports utilizing concave diffusers for increased dispersion of low frequencies. Ports are rubber coated for more luxurious look and to provide even better effect on a sound performance.
 

B-60: Low-turbulence and high-velocity port provides exceptional dispersion of low frequencies.


CROSSOVER / INTERNAL WIRING

High quality, close-tolerance and precisely selected crossover components and internal wires for absolute sound neutrality, long-term high power and reliability.

TAGA Harmony utilizes the high quality of OFC internal wiring connecting crossovers with drivers assuring that incoming audio signals from a receiver or amplifier will not lose any important details on the paths to drivers.


BINDING POSTS

The high quality, gold-plated banana binding posts are accepting raw speaker cables up to 10AWG and most popular types of connectors. They offer bi-wiring and bi-amping for wider dispersions and spaciousness, higher sonic accuracy and more precise sound.

We use high-end 4N pure oxygen free copper wire jumpers terminated with gold-plated banana and spades connectors.